Page 1 of 2 12 LastLast
Results 1 to 15 of 22

Thread: Cylinder head gasket

  1. #1
    Join Date
    Apr 2003
    Location
    Belgium
    Posts
    234

    Cylinder head gasket

    Is it hard to replace a cylinder-head gasket on an old-fashioned 4-cylinder pushrod engine if you have never done it before?
    What are the main points to pay attention to?

  2. #2
    Join Date
    Nov 2004
    Posts
    50
    the main point is, let an expert do it, because if you get it wrong, you mite hav to write your car off

  3. #3
    Join Date
    Feb 2004
    Posts
    2,266
    4 cylinder pushrod wtf ...wow that thing must be wide

  4. #4
    Join Date
    May 2004
    Location
    Texas, USA
    Posts
    813
    their almost normal, cept those got pushrods to 1 of the sides.

    it is hard, tho if the engine is carbed then it mite be a bit easier as you don't have to disconnect so many cables.
    its hard cause removin the head.....is a lot.
    tho its easier on those than on DOHC engines since settin the timing easier.

    if you got all the tools and a book to read step by step, you can do it yourself.
    if you have totally no experience at all.....let an expert do it.
    oh and be very organized with the bolts and nuts and everything else.
    1993 nissan 240sx hatchback(stock) <<drifter, straight liner, road courser

    "Horsepower is the force that determines how fast you hit the wall. Torque is the force that determines how far you take the wall with you after you hit it."

    "Horsepower sells cars, torque wins races" - Carroll Shelby

    "Real cars don't make power at the front wheels....they lift them."

  5. #5
    Join Date
    Feb 2004
    Location
    Connecticut, USA
    Posts
    6,065
    Quote Originally Posted by KnifeEdge_2K1
    4 cylinder pushrod wtf ...wow that thing must be wide
    MG midgets have inline 4's with pushrods, heres a pic:
    http://www.fincars.com/images/kuvat/engine.jpg

    Taking off the head on a mg is quite easy, take off the carbs, disconnect coolant hoses, take off vavle cover, take off rockers, take off the head bolts, and there you go.
    "We went to Wnedy's. I had chicken nuggest." ~ Quiggs

  6. #6
    Join Date
    Sep 2004
    Location
    Californian by nature, living in Teggsas.
    Posts
    4,130
    Actually, be thankful it's a pushrod engine. That makes it a ton less complicated compared to doing it on an OHC car.
    An it harm none, do as ye will

    Approximately 79% of statistics are made up.

  7. #7
    Join Date
    Dec 2003
    Location
    nr Edinburgh, Whisky-soaked Scotland
    Posts
    27,775
    best to let us know your experience and tools.

    Coz taking it off is the easy bit

    Everything covered so far ...
    BUT, find out if the engine uses sacrificial head bolts. These are one-off use as they stretch when tightened up to provide the correct pressure. Using old ones risks threading a hole or even cracking a head !!
    When putting it together you'll need a torque wrnch and know how to use it.

    it is about the easiest job ON a car as long as you're methodical. marking everything knowing EXACLTY where it came from ( ie which rod goes where and which head bolt goes where ) and use the right tools.

    Why not tell us what car it is, likely someone will have done it and can wanr of any gotchas - beyond those listed in posts already.
    "A woman without curves is like a road without bends, you might get to your destination quicker but the ride is boring as hell'

  8. #8
    Join Date
    Dec 2003
    Location
    nr Edinburgh, Whisky-soaked Scotland
    Posts
    27,775
    Quote Originally Posted by jcp123
    Actually, be thankful it's a pushrod engine. That makes it a ton less complicated compared to doing it on an OHC car.
    Sorry but this is a DEPENDS, jcp.
    The pinto OHC is actually EASIER as there is no need to worry about which 'rod goes where and the timing is childsplay with no complicated belt route or overly-complex adjsuter settings.

    Just adding that $0.02 so folks dont' get frightened for the wrong reasons
    "A woman without curves is like a road without bends, you might get to your destination quicker but the ride is boring as hell'

  9. #9
    Join Date
    Apr 2003
    Location
    Rozenburg
    Posts
    10,012
    The torque wrench is the most important you'll need. It's very important to tighten the bolts in the right order and at the right torque.
    If you should see a man walking down a crowded street talking aloud to himself, don't run in the opposite direction, but run towards him, because he's a poet. You have nothing to fear from the poet - but the truth.

    (Ted Joans)

  10. #10
    Join Date
    Apr 2003
    Location
    Belgium
    Posts
    234
    It's a rudimentary Ford 1.3 X-flow.

  11. #11
    Join Date
    Dec 2003
    Location
    nr Edinburgh, Whisky-soaked Scotland
    Posts
    27,775
    Quote Originally Posted by Cedric
    It's a rudimentary Ford 1.3 X-flow.
    Nothing rudimentary about it.
    Was state-of-the-art when it came out .
    Great little engine that you can REALLY tune up if you chose
    What carbs ??

    Anyway, how are you on tools and basic isntruction ?
    If anything above kindergarten on those then go get yourself a Haynes manual for the car. A good torque wrench and a full gasket set.

    Follow the instructions and it REALLY IS the easiest job to do.

    Should have asked the first time ... do you havce a mate or a parents mate who does his/her own spannering ? Ask them to help you out the first time or at least to be around when you're putting it back together. Being able to ask for help is the most important step in any learning
    Last edited by Matra et Alpine; 11-21-2004 at 03:49 AM.
    "A woman without curves is like a road without bends, you might get to your destination quicker but the ride is boring as hell'

  12. #12
    Join Date
    Sep 2004
    Location
    Californian by nature, living in Teggsas.
    Posts
    4,130
    Quote Originally Posted by Matra et Alpine
    Sorry but this is a DEPENDS, jcp.
    The pinto OHC is actually EASIER as there is no need to worry about which 'rod goes where and the timing is childsplay with no complicated belt route or overly-complex adjsuter settings.

    Just adding that $0.02 so folks dont' get frightened for the wrong reasons

    Dunno...pushrods are easy to run up through the right hole (seeing as how they'll only go through in one angle), re-degreeing the cam correctly when you slap the OHC head on isn't nearly as easy.
    An it harm none, do as ye will

    Approximately 79% of statistics are made up.

  13. #13
    Join Date
    Dec 2003
    Location
    nr Edinburgh, Whisky-soaked Scotland
    Posts
    27,775
    Quote Originally Posted by jcp123
    Dunno...pushrods are easy to run up through the right hole (seeing as how they'll only go through in one angle), re-degreeing the cam correctly when you slap the OHC head on isn't nearly as easy.
    Don't need to re-degree it with some engines. eg the stock pinto
    The belt drive is accurate enough to retain the original timing and the small difference caused by the slightly thicker (new) gasket is not an issue except for the highest tune was where I was coming from.
    hence the citing the pinto OHC engine

    Yep on others where the timing is much more critical then you need to vernier the cam in.

    BUT in reality no harder than habving to adjust each rocker on a 'rod engine after fitting a new gasket. Coz now the slightly thicker (new) gasket translates directly to valve opening and rocker gap.

    The major point on 'rods is making sure you put the rod back in the same hole it came out of. It's a common noob error

    It still comes back to little difference on simple engines. Now a full on DOHC with very tight overlap is another matter But there again 'rods on a 4-valver would be a bloody nightmare too
    "A woman without curves is like a road without bends, you might get to your destination quicker but the ride is boring as hell'

  14. #14
    Join Date
    Sep 2004
    Location
    Californian by nature, living in Teggsas.
    Posts
    4,130
    i'm not sure i believe you, but never having touched an OHC car, i won't say you're wrong...
    An it harm none, do as ye will

    Approximately 79% of statistics are made up.

  15. #15
    Join Date
    Dec 2003
    Location
    nr Edinburgh, Whisky-soaked Scotland
    Posts
    27,775
    Quote Originally Posted by jcp123
    i'm not sure i believe you, but never having touched an OHC car, i won't say you're wrong...
    trust me, my boy

    You are spot on with an engine that's tuned up, jcp.
    I wouldn't want to NOT re-gap rockers on a pushrod engine or adjust timing on the cam no matter WHAT the manual said for a tuned engine.

    As the reason most of us would go DOHC is to get best performance out of smallest displacement then I'd always set it up spot on. Especially as usually a high tune setup will have the valves go INTO the piston space. So if the timing's out you'll bend valves and punch holes in pistons - not a pretty sound

    However, to go over the engineering, retiming a OHC only requires slackening of the bolts on the end of the cam, rotating it to marks ( using a simple vernier guage ) and tightening the bolts again. The equivalent task on a 'rod engine needs EACH rocker to be loosedned, gapped and re-tightened. It's quicker to do one cam on a vernier than 8 rockers In each case the task is not complex on most engines.
    Last edited by Matra et Alpine; 11-21-2004 at 04:50 PM.
    "A woman without curves is like a road without bends, you might get to your destination quicker but the ride is boring as hell'

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Head of Audi of America fired.
    By Quiggs in forum General Automotive
    Replies: 13
    Last Post: 11-18-2004, 12:41 PM
  2. 3 cylinder engines
    By KnifeEdge_2K1 in forum Technical forums
    Replies: 5
    Last Post: 06-12-2004, 06:49 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •